$ 2216/MT
- Density: 1.25 g/cc
- Density: 1.40 g/cc
- Water Absorption at Saturation: 0.080 %
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0070 cm/cm
$ 2203/MT
- Density: 1.56 g/cc
- Tensile Strength at Break: 142 MPa
- Elongation at Break: 2.0 %
- Tensile Modulus: 10.6 GPa
- Flexural Strength: 215 MPa
$ 1657/MT
- Density: 1.05 g/cc
- Density: 1.23 g/cc
- Water Absorption: 0.34 % @Thickness 2.00 mm
- Moisture Absorption: 0.110 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.080 %
$ 1538/MT
- Density: 1.46 g/cc
- Water Absorption: 0.39 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.018 cm/cm
- Linear Mold Shrinkage, Flow: 0.022 cm/cm
$ 2458/MT
- Density: 1.31 g/cc
- Linear Mold Shrinkage, Flow: 0.019 cm/cm
- Linear Mold Shrinkage, Transverse: 0.019 cm/cm
- Tensile Strength, Yield: 60.0 MPa
- Elongation at Break: 15 %
$ 1748/MT
- Density: 1.159 g/cc
- Linear Mold Shrinkage, Flow: 0.00020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0037 cm/cm
- Melt Flow: 5.3 g/10 min @Load 2.16 kg, Temperature 190 °C
- Hardness, Shore D: 38 @Temperature 23.0 °C, Time 15.0 sec
$ 2030/MT
- Density: 1.46 g/cc
- Linear Mold Shrinkage, Flow: 0.018 cm/cm
- Linear Mold Shrinkage, Transverse: 0.016 cm/cm
- Tensile Strength, Yield: 65.0 MPa
- Elongation at Break: 7.2 %
$ 1575/MT
- Density: 1.73 g/cc
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0090 cm/cm
- Melt Flow: 70 g/10 min @Load 5.00 kg, Temperature 280 °C
- Tensile Strength at Break: 110 MPa
$ 1558/MT
- Density: 1.64 g/cc
- Linear Mold Shrinkage, Flow: 0.0030 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0080 cm/cm
- Melt Flow: 16 g/10 min @Load 5.00 kg, Temperature 280 °C
- Tensile Strength at Break: 207 MPa
$ 1594/MT
- Melting Point: 154 °C
- Volume Resistivity: >= 1.00e+15 ohm-cm
- Dielectric Strength: 34.0 kV/mm
- Dissipation Factor: 0.0060 @Frequency 100 Hz
- Dissipation Factor: 0.010 @Frequency 1.00e+6 Hz
$ 1777/MT
- Density: 1.00 g/cc
- Density: 1.18 g/cc
- Water Absorption: 0.60 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.60 %
$ 1683/MT
- Regional Availability: Asia Pacific
$ 1556/MT
- Density: 1.69 g/cc
- Viscosity: 110800 cP @Shear Rate 5000 1/s, Temperature 260 °C
- Viscosity: 124700 cP @Shear Rate 5000 1/s, Temperature 250 °C
- Viscosity: 141400 cP @Shear Rate 5000 1/s, Temperature 240 °C
- Viscosity: 348200 cP @Shear Rate 500 1/s, Temperature 260 °C
$ 2093/MT
- Density: 1.10 g/cc
- Hardness, Shore D: <= 40
- Tensile Strength at Break: 22.0 MPa
- Elongation at Break: >= 300 %
- Tensile Modulus: 0.0300 GPa
$ 1777/MT
- Density: 1.20 g/cc
- Tensile Strength at Break: 34.0 MPa
- Tensile Stress: 16.6 MPa @Strain 10.0 %
- Elongation at Break: 300 %
- Tensile Modulus: 0.262 GPa
$ 1493/MT
- Density: 1.03 g/cc
- Density: 1.20 g/cc
- Water Absorption: 0.50 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.30 %
$ 1623/MT
- Density: 1.17 g/cc
- Density: 1.34 g/cc
- Moisture Absorption: 0.300 % @Thickness 2.00 mm
- Viscosity: 62350 cP @Shear Rate 5000 1/s, Temperature 260 °C
- Viscosity: 70960 cP @Shear Rate 5000 1/s, Temperature 250 °C
$ 2319/MT
- Density: 1.03 g/cc
- Density: 1.11 g/cc
- Water Absorption: 0.70 % @Thickness 2.00 mm
- Moisture Absorption: 0.300 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.70 %
$ 2024/MT
- Hardness, Shore D: <= 56
- Tensile Strength at Break: 40.0 MPa
- Elongation at Break: >= 300 %
- Tensile Modulus: 0.180 GPa
- Charpy Impact, Notched: NB
$ 2397/MT
- Density: 1.14 g/cc
- Water Absorption: 0.60 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.60 %
- Linear Mold Shrinkage, Flow: 0.011 cm/cm
$ 1901/MT
- Density: 1.12 g/cc
- Density: 1.30 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity Test: 150 cm³/g
$ 1711/MT
- Density: 1.49 g/cc
- Filler Content: 30 %
- Tensile Strength at Break: 55.0 MPa @Temperature 150 °C
- Tensile Strength at Break: 71.0 MPa @Temperature 90.0 °C
- Tensile Strength at Break: 127 MPa @Temperature 23.0 °C
$ 2261/MT
- Density: 1.43 g/cc
- Filler Content: 15 %
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm @Thickness 2.00 mm
- Linear Mold Shrinkage, Transverse: 0.0090 cm/cm @Thickness 2.00 mm
- Tensile Strength at Break: 97.0 MPa @Temperature 23.0 °C
$ 1796/MT
- Density: 1.31 g/cc
- Density: 1.53 g/cc
- Viscosity: 74660 cP @Shear Rate 5000 1/s, Temperature 270 °C
- Viscosity: 85140 cP @Shear Rate 5000 1/s, Temperature 260 °C
- Viscosity: 98010 cP @Shear Rate 5000 1/s, Temperature 250 °C
$ 2166/MT
- Specific Gravity: 1.79 g/cc
- Density: 1.79 g/cc
- Filler Content: 43 %
- Water Absorption: 0.060 % @Temperature 23.0 °C
- Water Absorption: 0.11 % @Temperature 23.0 °C
$ 1933/MT
- Density: 1.02 g/cc
- Density: 1.16 g/cc
- Water Absorption: 0.70 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.60 %
$ 1670/MT
- Density: 1.11 g/cc
- Linear Mold Shrinkage, Flow: 0.0080 cm/cm
- Linear Mold Shrinkage, Flow: 0.0090 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0060 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0070 cm/cm
$ 1864/MT
- Melting Point: 147 °C
- Delivery Form: Pellets
- Regional Availability: Asia Pacific
- Regional Availability: Europe
- Regional Availability: Global
$ 2270/MT
- Specific Gravity: 1.64 g/cc
- Density: 1.64 g/cc
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0070 cm/cm
- Hardness, Rockwell M: 75
$ 1519/MT
- Density: 1.64 g/cc
- Water Absorption: 0.75 % @Thickness 2.00 mm
- Moisture Absorption: 0.100 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0070 cm/cm
$ 2046/MT
- Specific Gravity: 1.60 g/cc
- Tensile Strength at Break: 94.0 MPa
- Elongation at Break: 2.0 %
- Izod Impact, Unnotched (ISO): 500 kJ/m²
- Izod Impact Resistance: 5.90 J/cm²
$ 2325/MT
- Density: 1.40 g/cc
- Tensile Strength at Break: 110 MPa
- Elongation at Break: 2.3 %
- Tensile Modulus: 6.20 GPa
- Flexural Strength: 170 MPa
$ 2364/MT
- Density: 1.40 g/cc
- Tensile Strength at Break: 110 MPa
- Elongation at Break: 2.3 %
- Tensile Modulus: 6.20 GPa
- Flexural Strength: 170 MPa
$ 1521/MT
- Density: 1.40 g/cc
- Water Absorption at Saturation: 0.080 %
- Tensile Strength at Break: 125 MPa
- Elongation at Break: 3.0 %
- Tensile Modulus: 6.50 GPa
$ 1546/MT
- Density: 1.56 g/cc
- Tensile Strength at Break: 142 MPa
- Elongation at Break: 2.0 %
- Tensile Modulus: 10.6 GPa
- Flexural Strength: 215 MPa
$ 1916/MT
- Density: 1.56 g/cc
- Water Absorption at Saturation: 0.080 %
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0070 cm/cm
- Tensile Strength at Break: 165 MPa
$ 1681/MT
- Density: 1.32 g/cc
- Linear Mold Shrinkage, Flow: 0.016 cm/cm
- Linear Mold Shrinkage, Transverse: 0.016 cm/cm
- Tensile Strength, Yield: 60.0 MPa
- Elongation at Break: 15 %
$ 1688/MT
- Density: 1.12 g/cc
- Density: 1.32 g/cc
- Viscosity: 66880 cP @Shear Rate 5000 1/s, Temperature 270 °C
- Viscosity: 77790 cP @Shear Rate 5000 1/s, Temperature 260 °C
- Viscosity: 90760 cP @Shear Rate 5000 1/s, Temperature 250 °C
$ 1588/MT
- Density: 1.32 g/cc
- Linear Mold Shrinkage, Flow: 0.016 cm/cm
- Linear Mold Shrinkage, Transverse: 0.016 cm/cm
- Tensile Strength, Yield: 60.0 MPa
- Elongation at Break: 15 %
$ 2499/MT
- Density: 1.32 g/cc
- Linear Mold Shrinkage, Flow: 0.013 cm/cm
- Linear Mold Shrinkage, Transverse: 0.014 cm/cm
- Tensile Strength, Yield: 60.0 MPa
- Elongation at Break: 15 %
$ 1916/MT
- Density: 1.51 g/cc
- Density: 1.74 g/cc
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0050 cm/cm
- Melt Flow: 10 g/10 min @Load 2.16 kg, Temperature 280 °C
$ 2064/MT
- Density: 1.35 g/cc
- Density: 1.56 g/cc
- Water Absorption at Saturation: 0.080 %
- Viscosity: 80700 cP @Shear Rate 5000 1/s, Temperature 270 °C
- Viscosity: 91200 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 1624/MT
- Density: 1.32 g/cc
- Linear Mold Shrinkage, Flow: 0.013 cm/cm
- Linear Mold Shrinkage, Transverse: 0.014 cm/cm
- Tensile Strength, Yield: 60.0 MPa
- Elongation at Break: 15 %
$ 1454/MT
- Density: 1.47 g/cc
- Density: 1.66 g/cc
- Water Absorption: 0.30 % @Thickness 2.00 mm
- Moisture Absorption: 0.100 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0030 cm/cm
DuPont Performance Polymers Rynite® 415HP BK503 Polyethylene Terephthalate (PET) (Unverified Data**)
$ 2229/MT
- Density: 1.39 g/cc
- Tensile Strength at Break: 80.0 MPa
- Elongation at Break: 5.0 %
- Tensile Modulus: 4.50 GPa
- Flexural Modulus: 4.00 GPa
$ 1617/MT
- Density: 1.68 g/cc
- Water Absorption: 0.75 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0080 cm/cm
$ 1635/MT
- Density: 1.25 g/cc
- Hardness, Shore D: 66
- Hardness, Shore D: <= 70
- Tensile Strength at Break: 52.0 MPa
- Tensile Stress: 23.0 MPa @Strain 10.0 %
$ 2181/MT
- Density: 1.36 g/cc
- Density: 1.53 g/cc
- Water Absorption: 0.35 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Viscosity: 91150 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 2284/MT
- Density: 1.23 g/cc
- Linear Mold Shrinkage: 0.015 cm/cm @Thickness 2.00 mm
- Melt Flow: 14 g/10 min @Load 2.16 kg, Temperature 240 °C
- Hardness, Shore D: 65 @Time 15.0 sec
- Tensile Strength at Break: 30.0 MPa @Temperature 23.0 °C
$ 2381/MT
- Density: 1.44 g/cc
- Tensile Strength at Break: 125 MPa
- Elongation at Break: 2.0 %
- Tensile Modulus: 9.20 GPa
- Flexural Strength: 180 MPa
$ 1966/MT
- Density: 1.23 g/cc
- Melt Flow: 4.8 g/10 min @Load 2.16 kg, Temperature 230 °C
- Hardness, Shore D: <= 65
- Hardness, Shore D: 63 @Time 15.0 sec
- Tensile Strength at Break: 31.0 MPa @Temperature 23.0 °C
$ 1446/MT
- Density: 1.03 g/cc
- Density: 1.20 g/cc
- Water Absorption: 0.60 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.60 %
$ 1961/MT
- Density: 1.15 g/cc
- Linear Mold Shrinkage, Flow: 0.0070 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0050 cm/cm
- Melt Flow: 10 g/10 min @Load 5.00 kg, Temperature 190 °C
- Hardness, Shore D: 21
$ 1465/MT
- Density: 1.19 g/cc
- Density: 1.35 g/cc
- Water Absorption: 0.78 % @Thickness 2.00 mm
- Moisture Absorption: 0.260 % @Thickness 2.00 mm
- Viscosity: 64000 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 2090/MT
- Density: 1.46 g/cc
- Density: 1.67 g/cc
- Viscosity: 75510 cP @Shear Rate 5000 1/s, Temperature 270 °C
- Viscosity: 91440 cP @Shear Rate 5000 1/s, Temperature 260 °C
- Viscosity: 112800 cP @Shear Rate 5000 1/s, Temperature 250 °C
$ 1629/MT
- Density: 1.36 g/cc
- Density: 1.52 g/cc
- Water Absorption: 0.78 % @Thickness 2.00 mm
- Moisture Absorption: 0.230 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0040 cm/cm
$ 1985/MT
- Density: 1.22 g/cc
- Linear Mold Shrinkage, Flow: 0.018 cm/cm
- Linear Mold Shrinkage, Transverse: 0.017 cm/cm
- Tensile Strength, Yield: 36.0 MPa
- Elongation at Break: >= 50 %
$ 1578/MT
- Specific Gravity: 1.58 g/cc
- Melt Flow: 9.0 g/10 min @Load 2.16 kg, Temperature 280 °C
- Hardness, Rockwell M: 100
- Hardness, Rockwell R: 120
- Tensile Strength at Break: 170 MPa
$ 1666/MT
- Density: 1.15 g/cc
- Water Absorption: 12 % @Thickness 2.00 mm
- Moisture Absorption: 0.800 % @Thickness 2.00 mm
- Water Absorption at Saturation: 6.9 %
- Linear Mold Shrinkage, Flow: 0.0070 cm/cm
$ 1880/MT
- Density: 1.11 g/cc
- Density: 1.31 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 88500 cP @Shear Rate 5000 1/s, Temperature 260 °C
DuPont Performance Polymers Crastin® 6131 NC010 Polybutylene Terephthalate (PBT) (Unverified Data**)
$ 2063/MT
- Density: 1.11 g/cc
- Density: 1.30 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 68390 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 2146/MT
- Density: 1.25 g/cc
- Hardness, Shore D: 66
- Hardness, Shore D: <= 70
- Tensile Strength at Break: 53.0 MPa
- Tensile Stress: 23.0 MPa @Strain 10.0 %
$ 2186/MT
- Density: 1.01 g/cc
- Density: 1.19 g/cc
- Water Absorption at Saturation: 2.5 %
- Viscosity: 47110 cP @Shear Rate 5000 1/s, Temperature 250 °C
- Viscosity: 51280 cP @Shear Rate 5000 1/s, Temperature 240 °C
$ 1566/MT
- Density: 1.19 g/cc
- Hardness, Shore D: <= 55
- Tensile Strength at Break: 44.0 MPa
- Elongation at Break: >= 300 %
- Charpy Impact, Notched: NB
$ 1878/MT
- Hardness, Shore D: <= 72
- Tensile Strength at Break: 53.0 MPa
- Elongation at Break: >= 300 %
- Tensile Modulus: 0.525 GPa
- Charpy Impact, Notched: 3.30 J/cm²
$ 1460/MT
- Density: 1.42 g/cc
- Density: 1.57 g/cc
- Water Absorption: 0.72 % @Thickness 2.00 mm
- Moisture Absorption: 0.210 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0030 cm/cm
$ 1551/MT
- Density: 0.995 g/cc
- Density: 1.16 g/cc
- Linear Mold Shrinkage, Flow: 0.012 cm/cm
- Linear Mold Shrinkage, Transverse: 0.012 cm/cm
- Melt Flow: 13 g/10 min @Load 2.16 kg, Temperature 240 °C
$ 1532/MT
- Density: 1.03 g/cc
- Density: 1.18 g/cc
- Water Absorption: 3.7 % @Thickness 2.00 mm
- Moisture Absorption: 0.400 % @Thickness 2.00 mm
- Water Absorption at Saturation: 2.1 %
$ 1663/MT
- Density: 1.11 g/cc
- Density: 1.30 g/cc
- Water Absorption: 0.50 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 116000 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 1883/MT
- Density: 1.13 g/cc
- Density: 1.28 g/cc
- Water Absorption: 0.60 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.30 %
$ 1680/MT
- Density: 1.28 g/cc
- Density: 1.44 g/cc
- Water Absorption: 0.72 % @Thickness 2.00 mm
- Moisture Absorption: 0.240 % @Thickness 2.00 mm
- Viscosity: 67000 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 1445/MT
- Specific Gravity: 1.51 g/cc
- Density: 1.49 g/cc
- Filler Content: 30 %
- Water Absorption: 0.060 % @Temperature 23.0 °C
- Viscosity: 110000 cP @Shear Rate 3090 1/s, Temperature 305 °C
$ 1678/MT
- Density: 1.57 g/cc
- Linear Mold Shrinkage, Flow: 0.0030 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0070 cm/cm
- Tensile Strength at Break: 80.0 MPa
- Tensile Stress: 1.94 MPa @Strain 0.0700 %, Temperature 150 °C
$ 2161/MT
- Density: 1.38 g/cc
- Filler Content: 20 %
- Water Absorption: 0.40 % @Temperature 23.0 °C
- Tensile Strength at Break: 95.0 MPa @Temperature 23.0 °C
- Elongation at Break: 2.9 % @Temperature 23.0 °C
$ 1536/MT
- Density: 1.25 g/cc
- Density: 1.45 g/cc
- Water Absorption: 0.35 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 157000 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 1562/MT
- Density: 1.28 g/cc
- Hardness, Shore D: <= 82
- Tensile Strength at Break: 50.0 MPa
- Elongation at Break: >= 300 %
- Charpy Impact, Notched: 1.50 J/cm²
$ 1610/MT
- Density: 1.63 g/cc
- Water Absorption: 0.32 % @Thickness 2.00 mm
- Moisture Absorption: 0.130 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0050 cm/cm
- Linear Mold Shrinkage, Flow: 0.0060 cm/cm
$ 1606/MT
- Density: 1.37 g/cc
- Density: 1.58 g/cc
- Water Absorption: 0.33 % @Thickness 2.00 mm
- Moisture Absorption: 0.140 % @Thickness 2.00 mm
- Viscosity: 102700 cP @Shear Rate 5000 1/s, Temperature 260 °C
DuPont Performance Polymers Crastin® 6130 NC010 Polybutylene Terephthalate (PBT) (Unverified Data**)
$ 1969/MT
- Density: 1.11 g/cc
- Density: 1.30 g/cc
- Viscosity: 102200 cP @Shear Rate 5000 1/s, Temperature 260 °C
- Viscosity: 113100 cP @Shear Rate 5000 1/s, Temperature 250 °C
- Viscosity: 125300 cP @Shear Rate 5000 1/s, Temperature 240 °C
$ 1618/MT
- Density: 1.64 g/cc
- Water Absorption: 0.60 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0090 cm/cm
$ 1589/MT
- Density: 1.49 g/cc
- Density: 1.71 g/cc
- Water Absorption: 0.30 % @Thickness 2.00 mm
- Moisture Absorption: 0.100 % @Thickness 2.00 mm
- Viscosity: 110800 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 1603/MT
- Density: 1.22 g/cc
- Hardness, Shore D: <= 63
- Tensile Strength at Break: 41.0 MPa
- Elongation at Break: >= 300 %
- Tensile Modulus: 0.260 GPa
$ 1657/MT
- Density: 1.15 g/cc
- Hardness, Shore D: <= 40
- Tensile Strength at Break: 26.0 MPa
- Elongation at Break: >= 300 %
- Charpy Impact, Notched: NB
$ 1530/MT
- Density: 1.71 g/cc
- Tensile Strength at Break: 145 MPa
- Elongation at Break: 1.7 %
- Tensile Modulus: 15.7 GPa
- Flexural Strength: 210 MPa
$ 1545/MT
- Density: 1.00 g/cc
- Density: 1.17 g/cc
- Water Absorption: 0.50 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.50 %
$ 1710/MT
- Density: 1.14 g/cc
- Water Absorption: 0.50 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Melt Flow: 0.90 g/10 min @Load 2.16 kg, Temperature 230 °C
- Hardness, Shore D: 37
$ 2345/MT
- Density: 1.26 g/cc
- Density: 1.45 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Viscosity: 80120 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 2096/MT
- Density: 1.31 g/cc
- Tensile Strength, Yield: 58.0 MPa
- Elongation at Break: 30 %
- Elongation at Yield: 6.0 %
- Tensile Modulus: 2.60 GPa
$ 1526/MT
- Density: 1.31 g/cc
- Tensile Strength, Yield: 58.0 MPa
- Elongation at Break: 30 %
- Elongation at Yield: 6.0 %
- Tensile Modulus: 2.60 GPa
$ 1777/MT
- Density: 1.31 g/cc
- Linear Mold Shrinkage, Flow: 0.020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.018 cm/cm
- Tensile Strength, Yield: 60.0 MPa
- Elongation at Break: 13 %
$ 1550/MT
- Density: 1.61 g/cc
- Melt Flow: 17 g/10 min @Load 2.16 kg, Temperature 280 °C
- Tensile Strength at Break: 145 MPa
- Tensile Stress: 6.65 MPa @Strain 0.190 %, Temperature 150 °C
- Tensile Stress: 11.36 MPa @Strain 0.230 %, Temperature 90.0 °C
$ 2085/MT
- Density: 1.12 g/cc
- Density: 1.30 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity Test: 130 cm³/g
$ 1619/MT
- Density: 1.31 g/cc
- Linear Mold Shrinkage, Flow: 0.017 cm/cm
- Linear Mold Shrinkage, Transverse: 0.017 cm/cm
- Melt Flow: 18 g/10 min @Load 2.16 kg, Temperature 250 °C
- Tensile Strength, Yield: 57.0 MPa
$ 1631/MT
- Density: 1.04 g/cc
- Density: 1.22 g/cc
- Water Absorption: 0.60 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 94540 cP @Shear Rate 5000 1/s, Temperature 250 °C
DuPont Performance Polymers Rynite® 415HP NC010 Polyethylene Terephthalate (PET) (Unverified Data**)
$ 1724/MT
- Specific Gravity: 1.39 g/cc
- Density: 1.39 g/cc
- Water Absorption: 2.5 % @Thickness 2.00 mm
- Moisture Absorption: 0.250 % @Thickness 2.00 mm
- Viscosity: 57000 cP @Shear Rate 5000 1/s, Temperature 315 °C
$ 1459/MT
- Density: 1.07 g/cc
- Hardness, Shore D: <= 30
- Tensile Strength at Break: 24.0 MPa
- Elongation at Break: >= 300 %
- Charpy Impact, Notched: NB
$ 1759/MT
- Density: 1.37 g/cc
- Water Absorption at Saturation: 0.080 %
- Linear Mold Shrinkage, Flow: 0.0050 cm/cm
- Linear Mold Shrinkage, Transverse: 0.011 cm/cm
- Hardness, Rockwell R: 117
$ 1584/MT
- Density: 1.11 g/cc
- Water Absorption: 0.70 % @Thickness 2.00 mm
- Moisture Absorption: 0.300 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0080 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0080 cm/cm
DuPont Performance Polymers Rynite® FG530 NC011 Polyethylene Terephthalate (PET) (Unverified Data**)
$ 1534/MT
- Density: 1.57 g/cc
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0080 cm/cm
- Tensile Strength at Break: 162 MPa
- Elongation at Break: 2.1 %
$ 1661/MT
- Density: 1.29 g/cc
- Density: 1.50 g/cc
- Water Absorption: 0.35 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Viscosity: 68560 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 2151/MT
- Density: 0.940 g/cc
- Density: 1.07 g/cc
- Water Absorption: 0.80 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.50 %
$ 1593/MT
- Density: 1.02 g/cc
- Density: 1.16 g/cc
- Water Absorption: 0.70 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
$ 1744/MT
- Density: 1.19 g/cc
- Density: 1.37 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 78230 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 1748/MT
- Density: 1.20 g/cc
- Melt Flow: 7.5 g/10 min @Load 10.0 kg, Temperature 250 °C
- Hardness, Shore D: 70 @Time 15.0 sec
- Tensile Strength at Break: 40.0 MPa @Temperature 23.0 °C
- Tensile Stress: 30.0 MPa @Strain 10.0 %, Temperature 23.0 °C
$ 1702/MT
- Density: 1.22 g/cc
- Hardness, Shore D: <= 63
- Tensile Strength at Break: 43.0 MPa
- Elongation at Break: >= 300 %
- Charpy Impact, Notched: 12.0 J/cm²
$ 1886/MT
- Density: 1.42 g/cc
- Tensile Strength at Break: 133 MPa
- Elongation at Break: 2.2 %
- Tensile Modulus: 9.60 GPa
- Izod Impact, Notched (ISO): 7.00 kJ/m²
$ 1861/MT
- Density: 1.35 g/cc
- Tensile Strength at Break: 108 MPa
- Elongation at Break: 2.5 %
- Tensile Modulus: 7.00 GPa
- Flexural Strength: 160 MPa
$ 1759/MT
- Density: 1.272 g/cc
- Linear Mold Shrinkage, Flow: 0.026 cm/cm @Thickness 2.00 mm
- Linear Mold Shrinkage, Transverse: 0.023 cm/cm @Thickness 2.00 mm
- Melt Flow: 2.0 g/10 min @Load 2.16 kg, Temperature 250 °C
- Melt Flow: 6.5 g/10 min @Load 2.16 kg, Temperature 250 °C
$ 1483/MT
- Density: 1.10 g/cc
- Hardness, Shore D: <= 40
- Tensile Strength at Break: 22.0 MPa
- Elongation at Break: >= 300 %
- Charpy Impact, Notched: NB
$ 2237/MT
- Specific Gravity: 1.15 g/cc
- Density: 1.15 g/cc
- Water Absorption: 5.0 % @Temperature 23.0 °C
- Water Absorption: 5.0 % @Temperature 23.0 °C
- Linear Mold Shrinkage: 0.0050 cm/cm
$ 2048/MT
- Density: 1.49 g/cc
- Linear Mold Shrinkage, Flow: 0.0070 cm/cm
- Linear Mold Shrinkage, Transverse: 0.010 cm/cm
- Tensile Strength at Break: 91.0 MPa
- Elongation at Break: 2.8 %
$ 2273/MT
- Density: 1.58 g/cc
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0070 cm/cm
- Tensile Strength at Break: 82.0 MPa
- Elongation at Break: 2.0 %
$ 1469/MT
- Density: 1.11 g/cc
- Density: 1.31 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 92000 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 1948/MT
- Specific Gravity: 1.18 g/cc
- Density: 1.18 g/cc
- Water Absorption: 0.20 % @Temperature 23.0 °C
- Water Absorption: 0.60 % @Temperature 23.0 °C
- Water Absorption: 0.60 % @Temperature 23.0 °C
$ 1506/MT
- Density: 1.46 g/cc
- Density: 1.67 g/cc
- Viscosity: 75510 cP @Shear Rate 5000 1/s, Temperature 270 °C
- Viscosity: 91440 cP @Shear Rate 5000 1/s, Temperature 260 °C
- Viscosity: 112800 cP @Shear Rate 5000 1/s, Temperature 250 °C
$ 1664/MT
- Density: 1.06 g/cc
- Density: 1.18 g/cc
- Water Absorption: 6.5 % @Thickness 2.00 mm
- Moisture Absorption: 0.700 % @Thickness 2.00 mm
- Water Absorption at Saturation: 3.4 %
$ 1508/MT
- Density: 1.36 g/cc
- Density: 1.54 g/cc
- Water Absorption: 0.35 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0030 cm/cm
$ 1519/MT
- Density: 1.06 g/cc
- Density: 1.22 g/cc
- Water Absorption: 0.60 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.50 %
$ 1498/MT
- Density: 1.38 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Viscosity: 175000 cP @Temperature 250 °C
- Viscosity: 55600 cP @Shear Rate 5000 1/s, Temperature 270 °C
$ 1756/MT
- Density: 1.30 g/cc
- Linear Mold Shrinkage, Flow: 0.018 cm/cm
- Linear Mold Shrinkage, Transverse: 0.017 cm/cm
- Melt Flow: 10.1 g/10 min @Load 2.16 kg, Temperature 250 °C
- Tensile Strength, Yield: 57.0 MPa
$ 1595/MT
- Density: 1.32 g/cc
- Linear Mold Shrinkage, Flow: 0.017 cm/cm
- Linear Mold Shrinkage, Transverse: 0.016 cm/cm
- Tensile Strength, Yield: 60.0 MPa
- Elongation at Break: 13 %
$ 1650/MT
- Density: 1.54 g/cc
- Water Absorption: 0.35 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0080 cm/cm
- Linear Mold Shrinkage, Transverse: 0.013 cm/cm
$ 1792/MT
- Density: 1.50 g/cc
- Water Absorption: 0.35 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Viscosity: 230000 cP @Temperature 250 °C
- Viscosity: 68400 cP @Shear Rate 5000 1/s, Temperature 270 °C
$ 2280/MT
- Density: 1.63 g/cc
- Linear Mold Shrinkage, Flow: 0.0040 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0080 cm/cm
- Melt Flow: 20 g/10 min @Load 2.16 kg, Temperature 280 °C
- Tensile Strength at Break: 110 MPa
$ 1794/MT
- Density: 1.17 g/cc
- Density: 1.37 g/cc
- Linear Mold Shrinkage, Flow: 0.020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.016 cm/cm
- Tensile Stress: 5.62 MPa @Strain 1.20 %, Temperature 90.0 °C
$ 2248/MT
- Density: 1.30 g/cc
- Density: 1.43 g/cc
- Water Absorption at Saturation: 1.9 %
- Linear Mold Shrinkage, Flow: 0.011 cm/cm
- Linear Mold Shrinkage, Transverse: 0.011 cm/cm
$ 2523/MT
- Density: 1.14 g/cc
- Density: 1.37 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Viscosity: 55190 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 2199/MT
- Specific Gravity: 1.16 g/cc
- Density: 1.16 g/cc
- Water Absorption: 0.20 % @Temperature 23.0 °C
- Water Absorption: 0.70 % @Temperature 23.0 °C
- Water Absorption: 0.70 % @Temperature 23.0 °C
$ 1454/MT
- Density: 1.15 g/cc
- Melt Flow: 0.40 g/10 min @Load 2.16 kg, Temperature 220 °C
- Melt Flow: 4.0 g/10 min @Load 10.0 kg, Temperature 220 °C
- Hardness, Shore D: 41
- Hardness, Shore D: <= 45
$ 1603/MT
- Density: 1.22 g/cc
- Density: 1.42 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Viscosity: 54480 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 1667/MT
- Density: 1.07 g/cc
- Hardness, Shore D: <= 30
- Tensile Strength at Break: 24.0 MPa
- Elongation at Break: >= 300 %
- Charpy Impact, Notched: NB
$ 1618/MT
- Density: 1.07 g/cc
- Density: 1.23 g/cc
- Water Absorption: 0.60 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.014 cm/cm
$ 1837/MT
- Density: 1.11 g/cc
- Density: 1.31 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 75900 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 2012/MT
- Density: 1.61 g/cc
- Linear Mold Shrinkage, Flow: 0.0030 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0090 cm/cm
- Tensile Strength at Break: 117 MPa
- Elongation at Break: 2.6 %
$ 1544/MT
- Density: 1.21 g/cc
- Water Absorption: 0.50 % @Temperature 23.0 °C
- Water Absorption: 1.5 % @Temperature 23.0 °C
- Water Absorption: 2.2 % @Temperature 23.0 °C
- Hardness, Shore D: 54 @Time 15.0 sec
$ 1470/MT
- Density: 1.16 g/cc
- Water Absorption: 0.20 % @Temperature 23.0 °C
- Water Absorption: 0.60 % @Temperature 23.0 °C
- Water Absorption: 0.40 % @Thickness 1.00 mm, Temperature 23.0 °C
- Linear Mold Shrinkage, Flow: 0.012 cm/cm @Thickness 2.00 mm
$ 2172/MT
- Density: 1.28 g/cc
- Hardness, Shore D: <= 82
- Tensile Strength at Break: 50.0 MPa
- Elongation at Break: >= 300 %
- Tensile Modulus: 1.18 GPa
$ 1602/MT
- Density: 1.00 g/cc
- Density: 1.17 g/cc
- Water Absorption: 0.50 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.014 cm/cm
$ 1517/MT
- Density: 1.11 g/cc
- Density: 1.31 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 66530 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 1478/MT
- Density: 1.11 g/cc
- Density: 1.31 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 88500 cP @Shear Rate 5000 1/s, Temperature 260 °C
DuPont Performance Polymers Rynite® FR515 BK507 Polyethylene Terephthalate (PET) (Unverified Data**)
$ 1483/MT
- Density: 1.55 g/cc
- Tensile Strength at Break: 100 MPa
- Elongation at Break: 2.2 %
- Tensile Modulus: 6.135 GPa
- Flexural Strength: 160 MPa
$ 1580/MT
- Density: 1.05 g/cc
- Density: 1.22 g/cc
- Water Absorption: 2.2 % @Thickness 2.00 mm
- Moisture Absorption: 0.400 % @Thickness 2.00 mm
- Water Absorption at Saturation: 1.6 %
$ 1631/MT
- Density: 1.69 g/cc
- Water Absorption: 0.62 % @Thickness 2.00 mm
- Moisture Absorption: 0.140 % @Thickness 2.00 mm
- Viscosity: 43000 cP @Shear Rate 5000 1/s, Temperature 305 °C
- Viscosity: 55000 cP @Shear Rate 5000 1/s, Temperature 295 °C
$ 1446/MT
- Density: 1.50 g/cc
- Water Absorption: 0.35 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Viscosity: 230000 cP @Temperature 250 °C
- Linear Mold Shrinkage, Flow: 0.0030 cm/cm
$ 2023/MT
- Density: 1.68 g/cc
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0080 cm/cm
- Tensile Strength at Break: 130 MPa
- Elongation at Break: 1.9 %
$ 2087/MT
- Density: 1.31 g/cc
- Melt Flow: 32.9 g/10 min @Load 2.16 kg, Temperature 250 °C
- Tensile Strength, Yield: 58.0 MPa
- Elongation at Break: 20 %
- Elongation at Yield: 6.0 %
$ 1578/MT
- Density: 1.52 g/cc
- Tensile Strength at Break: 130 MPa
- Elongation at Break: 2.5 %
- Tensile Modulus: 9.60 GPa
- Flexural Strength: 200 MPa
$ 1680/MT
- Density: 1.18 g/cc
- Water Absorption: 6.8 % @Thickness 2.00 mm
- Moisture Absorption: 0.700 % @Thickness 2.00 mm
- Water Absorption at Saturation: 3.5 %
- Linear Mold Shrinkage, Flow: 0.0050 cm/cm
$ 1645/MT
- Density: 1.70 g/cc
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0080 cm/cm
- Tensile Strength at Break: 175 MPa
- Elongation at Break: 1.9 %
$ 1695/MT
- Density: 1.07 g/cc
- Water Absorption: 0.80 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0060 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0060 cm/cm
$ 1522/MT
- Density: 1.34 g/cc
- Tensile Strength at Break: 115 MPa
- Elongation at Break: 2.3 %
- Tensile Modulus: 7.30 GPa
- Izod Impact, Notched (ISO): 6.50 kJ/m²
$ 1833/MT
- Density: 1.58 g/cc
- Tensile Strength at Break: 100 MPa
- Elongation at Break: 3.4 %
- Tensile Modulus: 7.20 GPa
- Flexural Strength: 155 MPa
$ 1448/MT
- Density: 1.32 g/cc
- Water Absorption: 0.20 % @Temperature 23.0 °C
- Water Absorption: 0.40 % @Temperature 23.0 °C
- Linear Mold Shrinkage, Flow: 0.022 cm/cm @Thickness 2.00 mm
- Linear Mold Shrinkage, Transverse: 0.022 cm/cm @Thickness 2.00 mm
$ 2251/MT
- Density: 1.55 g/cc
- Tensile Strength at Break: 115 MPa
- Elongation at Break: 1.7 %
- Tensile Modulus: 10.2 GPa
- Flexural Strength: 160 MPa
$ 1699/MT
- Density: 1.31 g/cc
- Tensile Strength, Yield: 59.0 MPa
- Elongation at Break: 30 %
- Elongation at Yield: 8.0 %
- Tensile Modulus: 2.60 GPa
$ 2016/MT
- Density: 1.38 g/cc
- Water Absorption: 0.40 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Viscosity: 175000 cP @Temperature 250 °C
- Linear Mold Shrinkage, Flow: 0.0050 cm/cm
$ 1526/MT
- Density: 1.41 g/cc
- Tensile Strength at Break: 102 MPa
- Elongation at Break: 3.4 %
- Tensile Modulus: 5.70 GPa
- Izod Impact, Notched (ISO): 5.00 kJ/m²
$ 2334/MT
- Specific Gravity: 1.58 g/cc
- Density: 1.58 g/cc
- Water Absorption: 0.83 % @Thickness 2.00 mm
- Moisture Absorption: 0.130 % @Thickness 2.00 mm
- Viscosity: 37000 cP @Shear Rate 5000 1/s, Temperature 315 °C
$ 1580/MT
- Specific Gravity: 1.56 g/cc
- Density: 1.56 g/cc
- Water Absorption: 0.70 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Viscosity: 44000 cP @Shear Rate 5000 1/s, Temperature 300 °C
DuPont Performance Polymers Rynite® FR531 NC010 Polyethylene Terephthalate (PET) (Unverified Data**)
$ 1630/MT
- Density: 1.83 g/cc
- Linear Mold Shrinkage, Flow: 0.0010 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0070 cm/cm
- Melt Flow: 3.0 g/10 min @Load 5.00 kg, Temperature 280 °C
- Tensile Strength at Break: 129 MPa
$ 1606/MT
- Density: 1.72 g/cc
- Filler Content: 50 %
- Water Absorption: 0.10 % @Temperature 23.0 °C
- Water Absorption: 0.20 % @Temperature 23.0 °C
- Viscosity: 62000 cP @Shear Rate 10000 1/s, Temperature 270 °C
$ 2501/MT
- Density: 1.44 g/cc
- Tensile Strength at Break: 130 MPa
- Elongation at Break: 2.5 %
- Tensile Modulus: 9.50 GPa
- Charpy Impact Unnotched: 6.00 J/cm²
$ 2282/MT
- Density: 1.14 g/cc
- Water Absorption: 0.40 % @Temperature 23.0 °C
- Melt Flow: 4.5 g/10 min @Load 10.0 kg, Temperature 250 °C
- Melt Flow: 20 g/10 min @Load 2.16 kg, Temperature 250 °C
- Hardness, Shore D: 62 @Time 15.0 sec
$ 2207/MT
- Density: 1.00 g/cc
- Density: 1.13 g/cc
- Water Absorption: 0.80 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.60 %
$ 1868/MT
- Density: 1.11 g/cc
- Density: 1.30 g/cc
- Water Absorption: 0.50 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.017 cm/cm
$ 2429/MT
- Density: 1.14 g/cc
- Water Absorption: 0.50 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Melt Flow: 0.90 g/10 min @Load 2.16 kg, Temperature 230 °C
- Melt Flow: 1.0 g/10 min @Load 2.16 kg, Temperature 230 °C
$ 2173/MT
- Density: 1.01 g/cc
- Density: 1.19 g/cc
- Viscosity: 114600 cP @Shear Rate 5000 1/s, Temperature 240 °C
- Viscosity: 143100 cP @Shear Rate 5000 1/s, Temperature 230 °C
- Viscosity: 511800 cP @Shear Rate 500 1/s, Temperature 240 °C
$ 1519/MT
- Density: 1.11 g/cc
- Linear Mold Shrinkage, Flow: 0.0090 cm/cm
- Linear Mold Shrinkage, Flow: 0.010 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0070 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0080 cm/cm
$ 2474/MT
- Density: 2.10 g/cc
- Melting Point: 200 °C
- Delivery Form: Pellets
- Processing: Casting
- Processing: Coatable
$ 1737/MT
- Density: 1.10 g/cc
- Density: 1.11 g/cc
- Water Absorption: 0.70 % @Thickness 2.00 mm
- Moisture Absorption: 0.300 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.70 %
$ 1626/MT
- Density: 1.56 g/cc
- Linear Mold Shrinkage, Flow: 0.0030 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0090 cm/cm
- Tensile Strength at Break: 150 MPa
- Elongation at Break: 2.1 %
$ 2362/MT
- Density: 1.03 g/cc
- Density: 1.21 g/cc
- Viscosity: 169000 cP @Shear Rate 5000 1/s, Temperature 260 °C
- Viscosity: 226000 cP @Shear Rate 5000 1/s, Temperature 250 °C
- Viscosity: 312000 cP @Shear Rate 5000 1/s, Temperature 240 °C
$ 1685/MT
- Density: 1.50 g/cc
- Linear Mold Shrinkage, Flow: 0.0070 cm/cm
- Linear Mold Shrinkage, Transverse: 0.010 cm/cm
- Tensile Strength at Break: 100 MPa
- Elongation at Break: 3.1 %
$ 1702/MT
- Density: 1.45 g/cc
- Tensile Strength at Break: 113 MPa
- Elongation at Break: 3.0 %
- Tensile Modulus: 6.90 GPa
- Flexural Strength: 175 MPa
DuPont Performance Polymers Rynite® FR530 NC010 Polyethylene Terephthalate (PET) (Unverified Data**)
$ 1727/MT
- Density: 1.68 g/cc
- Water Absorption: 0.75 % @Thickness 2.00 mm
- Moisture Absorption: 0.150 % @Thickness 2.00 mm
- Linear Mold Shrinkage, Flow: 0.0020 cm/cm
- Linear Mold Shrinkage, Transverse: 0.0080 cm/cm
$ 1475/MT
- Specific Gravity: 1.24 g/cc
- Density: 1.25 g/cc
- Water Absorption: 0.20 % @Temperature 23.0 °C
- Water Absorption: 0.20 % @Temperature 23.0 °C
- Melt Flow: 5.2 g/10 min @Load 2.16 kg, Temperature 190 °C
$ 1634/MT
- Density: 1.50 g/cc
- Tensile Strength at Break: 100 MPa
- Elongation at Break: 2.0 %
- Tensile Modulus: 7.80 GPa
- Flexural Strength: 140 MPa
$ 1859/MT
- Density: 1.03 g/cc
- Density: 1.22 g/cc
- Water Absorption: 0.31 % @Thickness 2.00 mm
- Moisture Absorption: 0.120 % @Thickness 2.00 mm
- Viscosity: 219200 cP @Shear Rate 5000 1/s, Temperature 250 °C
$ 1483/MT
- Density: 0.960 g/cc
- Density: 1.15 g/cc
- Water Absorption: 0.70 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.70 %
$ 1450/MT
- Density: 1.43 g/cc
- Filler Content: 5.0 %
- Linear Mold Shrinkage: 0.013 cm/cm @Thickness 3.20 mm
- Linear Mold Shrinkage: 0.014 cm/cm @Thickness 3.20 mm
- Tensile Strength at Break: 60.0 MPa @Temperature 23.0 °C
$ 1652/MT
- Density: 1.27 g/cc
- Density: 1.42 g/cc
- Water Absorption: 1.0 % @Thickness 2.00 mm
- Moisture Absorption: 0.250 % @Thickness 2.00 mm
- Viscosity: 72620 cP @Shear Rate 5000 1/s, Temperature 260 °C
$ 2049/MT
- Density: 1.03 g/cc
- Density: 1.19 g/cc
- Water Absorption: 0.60 % @Thickness 2.00 mm
- Moisture Absorption: 0.200 % @Thickness 2.00 mm
- Water Absorption at Saturation: 0.60 %
DuPont Performance Polymers Crastin® 6134 NC010 Polybutylene Terephthalate (PBT) (Unverified Data**)
$ 1585/MT
- Density: 1.30 g/cc
- Melt Flow: 33.5 g/10 min @Load 2.16 kg, Temperature 250 °C
- Tensile Strength, Yield: 59.0 MPa
- Elongation at Break: 45 %
- Elongation at Yield: 4.0 %
$ 1786/MT
- Density: 1.04 g/cc
- Density: 1.23 g/cc
- Viscosity: 91910 cP @Shear Rate 5000 1/s, Temperature 245 °C
- Viscosity: 99440 cP @Shear Rate 5000 1/s, Temperature 235 °C
- Viscosity: 108100 cP @Shear Rate 5000 1/s, Temperature 225 °C
$ 2409/MT
- Density: 1.22 g/cc
- Density: 1.41 g/cc
- Water Absorption: 0.42 % @Thickness 2.00 mm
- Moisture Absorption: 0.170 % @Thickness 2.00 mm
- Viscosity: 77750 cP @Shear Rate 5000 1/s, Temperature 260 °C
Delivery TP DuPont Performance Polymers
Below is a port-to-port container shipping rates chart for cost ranges of common international shipping destinations (from Saudi Arabia, Germany, China):| Country | 20’ Container | 40’ Container | 5,000 MT |
|---|---|---|---|
| 🇦🇺 Australia | $3345 | $4181 | $401400 |
| 🇦🇹 Austria | $2825 | $3531 | $339000 |
| 🇦🇿 Azerbaijan | $2625 | $3281 | $315000 |
| 🇦🇱 Albania | $2500 | $3125 | $300000 |
| 🇩🇿 Algeria | $2762.5 | $3453 | $331500 |
| 🇦🇴 Angola | $2762.5 | $3453 | $331500 |
| 🇦🇷 Argentina | $3230 | $4038 | $387600 |
| 🇦🇲 Armenia | $2625 | $3281 | $315000 |
| 🇦🇫 Afghanistan | $3712.5 | $4641 | $445500 |
| 🇧🇩 Bangladesh | $2625 | $3281 | $315000 |
| 🇧🇭 Bahrain | $3095 | $3869 | $371400 |
| 🇧🇾 Belarus | $2825 | $3531 | $339000 |
| 🇧🇿 Belize | $3155 | $3944 | $378600 |
| 🇧🇪 Belgium | $2575 | $3219 | $309000 |
| 🇧🇬 Bulgaria | $2400 | $3000 | $288000 |
| 🇧🇴 Bolivia | $3230 | $4038 | $387600 |
| 🇧🇦 Bosnia and Herzegovina | $2575 | $3219 | $309000 |
| 🇧🇷 Brazil | $3120 | $3900 | $374400 |
| 🇭🇺 Hungary | $2575 | $3219 | $309000 |
| 🇻🇪 Venezuela | $3230 | $4038 | $387600 |
| 🇻🇳 Vietnam | $2625 | $3281 | $315000 |
| 🇬🇭 Ghana | $2762.5 | $3453 | $331500 |
| 🇬🇹 Guatemala | $3230 | $4038 | $387600 |
| 🇬🇳 Guinea | $2762.5 | $3453 | $331500 |
| 🇩🇪 Germany | $2475 | $3094 | $297000 |
| 🇭🇳 Honduras | $3230 | $4038 | $387600 |
| 🇭🇰 Hong Kong S.A.R. | $2625 | $3281 | $315000 |
| 🇬🇷 Greece | $2575 | $3219 | $309000 |
| 🇬🇪 Georgia | $3712.5 | $4641 | $445500 |
| 🇩🇰 Denmark | $2400 | $3000 | $288000 |
| 🇩🇴 Dominican Republic | $3230 | $4038 | $387600 |
| 🇪🇬 Egypt | $2762.5 | $3453 | $331500 |
| 🇿🇲 Zambia | $2762.5 | $3453 | $331500 |
| 🇿🇼 Zimbabwe | $2762.5 | $3453 | $331500 |
| 🇮🇱 Israel | $2625 | $3281 | $315000 |
| 🇮🇳 India | $3712.5 | $4641 | $445500 |
| 🇮🇩 Indonesia | $3095 | $3869 | $371400 |
| 🇯🇴 Jordan | $2625 | $3281 | $315000 |
| 🇮🇶 Iraq | $2625 | $3281 | $315000 |
| 🇮🇷 Iran | $3095 | $3869 | $371400 |
| 🇮🇪 Ireland | $2500 | $3125 | $300000 |
| 🇮🇸 Iceland | $2575 | $3219 | $309000 |
| 🇪🇸 Spain | $2500 | $3125 | $300000 |
| 🇮🇹 Italy | $2400 | $3000 | $288000 |
| 🇾🇪 Yemen | $2625 | $3281 | $315000 |
| 🇰🇿 Kazakhstan | $2625 | $3281 | $315000 |
| 🇰🇭 Cambodia | $3095 | $3869 | $371400 |
| 🇨🇲 Cameroon | $2762.5 | $3453 | $331500 |
| 🇨🇦 Canada | $3230 | $4038 | $387600 |
| 🇶🇦 Qatar | $2625 | $3281 | $315000 |
| 🇰🇪 Kenya | $2762.5 | $3453 | $331500 |
| 🇨🇾 Cyprus | $2625 | $3281 | $315000 |
| 🇰🇬 Kyrgyzstan | $3095 | $3869 | $371400 |
| 🇨🇳 China | $3712.5 | $4641 | $445500 |
| 🇨🇴 Colombia | $3230 | $4038 | $387600 |
| 🇰🇷 Korea South | $2625 | $3281 | $315000 |
| 🇨🇷 Costa Rica | $3355 | $4194 | $402600 |
| 🇨🇮 Cote D'Ivoire (Ivory Coast) | $2762.5 | $3453 | $331500 |
| 🇨🇺 Cuba | $3230 | $4038 | $387600 |
| 🇰🇼 Kuwait | $2625 | $3281 | $315000 |
| 🇱🇻 Latvia | $2575 | $3219 | $309000 |
| 🇱🇧 Lebanon | $2625 | $3281 | $315000 |
| 🇱🇾 Libya | $2762.5 | $3453 | $331500 |
| 🇱🇹 Lithuania | $2500 | $3125 | $300000 |
| 🇱🇮 Liechtenstein | $2400 | $3000 | $288000 |
| 🇱🇺 Luxembourg | $2500 | $3125 | $300000 |
| 🇲🇾 Malaysia | $2625 | $3281 | $315000 |
| 🇲🇹 Malta | $2500 | $3125 | $300000 |
| 🇲🇦 Morocco | $2762.5 | $3453 | $331500 |
| 🇲🇽 Mexico | $3155 | $3944 | $378600 |
| 🇲🇩 Moldova | $2400 | $3000 | $288000 |
| 🇲🇨 Monaco | $2475 | $3094 | $297000 |
| 🇲🇳 Mongolia | $2625 | $3281 | $315000 |
| 🇲🇲 Myanmar | $2625 | $3281 | $315000 |
| 🇳🇦 Namibia | $2762.5 | $3453 | $331500 |
| 🇳🇵 Nepal | $2625 | $3281 | $315000 |
| 🇳🇬 Nigeria | $2762.5 | $3453 | $331500 |
| 🇳🇱 Netherlands | $2575 | $3219 | $309000 |
| 🇳🇮 Nicaragua | $3155 | $3944 | $378600 |
| 🇳🇿 New Zealand | $3345 | $4181 | $401400 |
| 🇳🇴 Norway | $2400 | $3000 | $288000 |
| 🇦🇪 United Arab Emirates | $3095 | $3869 | $371400 |
| 🇴🇲 Oman | $2625 | $3281 | $315000 |
| 🇵🇰 Pakistan | $2625 | $3281 | $315000 |
| 🇵🇦 Panama | $3230 | $4038 | $387600 |
| 🇵🇾 Paraguay | $3155 | $3944 | $378600 |
| 🇵🇪 Peru | $3230 | $4038 | $387600 |
| 🇵🇱 Poland | $2575 | $3219 | $309000 |
| 🇵🇹 Portugal | $2500 | $3125 | $300000 |
| 🇷🇺 Russia | $2575 | $3219 | $309000 |
| 🇷🇴 Romania | $2475 | $3094 | $297000 |
| 🇸🇦 Saudi Arabia | $2625 | $3281 | $315000 |
| 🇸🇳 Senegal | $2762.5 | $3453 | $331500 |
| 🇷🇸 Serbia | $2575 | $3219 | $309000 |
| 🇸🇬 Singapore | $3095 | $3869 | $371400 |
| 🇸🇾 Syria | $3095 | $3869 | $371400 |
| 🇸🇰 Slovakia | $2500 | $3125 | $300000 |
| 🇸🇮 Slovenia | $2500 | $3125 | $300000 |
| 🇬🇧 United Kingdom | $2475 | $3094 | $297000 |
| 🇸🇩 Sudan | $2762.5 | $3453 | $331500 |
| 🇺🇸 United States | $2902.5 | $3628 | $348300 |
| 🇹🇯 Tajikistan | $2625 | $3281 | $315000 |
| 🇹🇭 Thailand | $2625 | $3281 | $315000 |
| 🇹🇼 Taiwan | $3712.5 | $4641 | $445500 |
| 🇹🇿 Tanzania | $2762.5 | $3453 | $331500 |
| 🇹🇹 Trinidad And Tobago | $2675 | $3344 | $321000 |
| 🇹🇳 Tunisia | $2762.5 | $3453 | $331500 |
| 🇹🇲 Turkmenistan | $2625 | $3281 | $315000 |
| 🇹🇷 Turkey | $2625 | $3281 | $315000 |
| 🇺🇬 Uganda | $2762.5 | $3453 | $331500 |
| 🇺🇿 Uzbekistan | $2625 | $3281 | $315000 |
| 🇺🇦 Ukraine | $2500 | $3125 | $300000 |
| 🇺🇾 Uruguay | $2675 | $3344 | $321000 |
| 🇫🇴 Faroe Islands | $2575 | $3219 | $309000 |
| 🇵🇭 Philippines | $2625 | $3281 | $315000 |
| 🇫🇮 Finland | $2500 | $3125 | $300000 |
| 🇫🇷 France | $2575 | $3219 | $309000 |
| 🇭🇷 Croatia (Hrvatska) | $2575 | $3219 | $309000 |
| 🇲🇪 Montenegro | $2575 | $3219 | $309000 |
| 🇨🇿 Czech Republic | $2475 | $3094 | $297000 |
| 🇨🇱 Chile | $3355 | $4194 | $402600 |
| 🇨🇭 Switzerland | $2575 | $3219 | $309000 |
| 🇸🇪 Sweden | $2500 | $3125 | $300000 |
| 🇱🇰 Sri Lanka | $2625 | $3281 | $315000 |
| 🇪🇨 Ecuador | $3155 | $3944 | $378600 |
| 🇦🇸 American Samoa | $3345 | $4181 | $401400 |
| 🇸🇻 El Salvador | $3230 | $4038 | $387600 |
| 🇪🇪 Estonia | $2575 | $3219 | $309000 |
| 🇪🇹 Ethiopia | $2762.5 | $3453 | $331500 |
| 🇿🇦 South Africa | $2762.5 | $3453 | $331500 |
| 🇯🇵 Japan | $3095 | $3869 | $371400 |
| 🇦🇩 Andorra | $2500 | $3125 | $300000 |
| 🇦🇬 Antigua And Barbuda | $3155 | $3944 | $378600 |
| 🇧🇸 Bahamas, The | $3155 | $3944 | $378600 |
| 🇧🇧 Barbados | $3230 | $4038 | $387600 |
| 🇧🇹 Bhutan | $3095 | $3869 | $371400 |
| 🇧🇼 Botswana | $2762.5 | $3453 | $331500 |
| 🇸🇧 Solomon Islands | $3345 | $4181 | $401400 |
| 🇧🇳 Brunei | $2625 | $3281 | $315000 |
| 🇧🇮 Burundi | $2762.5 | $3453 | $331500 |
| 🇨🇻 Cabo Verde | $2762.5 | $3453 | $331500 |
| 🇨🇫 Central African Republic | $2762.5 | $3453 | $331500 |
| 🇹🇩 Chad | $2762.5 | $3453 | $331500 |
| 🇰🇲 Comoros | $2762.5 | $3453 | $331500 |
| 🇧🇯 Benin | $2762.5 | $3453 | $331500 |
| 🇩🇲 Dominica | $3230 | $4038 | $387600 |
| 🇬🇶 Equatorial Guinea | $2762.5 | $3453 | $331500 |
| 🇪🇷 Eritrea | $2762.5 | $3453 | $331500 |
| 🇫🇯 Fiji | $3345 | $4181 | $401400 |
| 🇩🇯 Djibouti | $2762.5 | $3453 | $331500 |
| 🇬🇦 Gabon | $2762.5 | $3453 | $331500 |
| 🇬🇲 Gambia, The | $2762.5 | $3453 | $331500 |
| 🇰🇮 Kiribati | $3345 | $4181 | $401400 |
| 🇬🇩 Grenada | $3355 | $4194 | $402600 |
| 🇬🇺 Guam | $3345 | $4181 | $401400 |
| 🇬🇾 Guyana | $3230 | $4038 | $387600 |
| 🇭🇹 Haiti | $3120 | $3900 | $374400 |
| 🇯🇲 Jamaica | $3230 | $4038 | $387600 |
| 🇰🇵 Korea, North | $2625 | $3281 | $315000 |
| 🇱🇸 Lesotho | $2762.5 | $3453 | $331500 |
| 🇲🇬 Madagascar | $2762.5 | $3453 | $331500 |
| 🇲🇼 Malawi | $2762.5 | $3453 | $331500 |
| 🇲🇻 Maldives | $2625 | $3281 | $315000 |
| 🇲🇱 Mali | $2762.5 | $3453 | $331500 |
| 🇲🇺 Mauritius | $2762.5 | $3453 | $331500 |
| 🇨🇼 Curaçao | $3230 | $4038 | $387600 |
| 🇦🇼 Aruba | $3120 | $3900 | $374400 |
| 🇻🇺 Vanuatu | $3345 | $4181 | $401400 |
| 🇳🇪 Niger | $2762.5 | $3453 | $331500 |
| 🇲🇵 Northern Mariana Islands | $3345 | $4181 | $401400 |
| 🇫🇲 Micronesia, Federated States Of | $3345 | $4181 | $401400 |
| 🇲🇭 Marshall Islands | $3345 | $4181 | $401400 |
| 🇵🇬 Papua New Guinea | $3345 | $4181 | $401400 |
| 🇬🇼 Guinea-Bissau | $2762.5 | $3453 | $331500 |
| 🇹🇱 Timor-Leste | $2625 | $3281 | $315000 |
| 🇷🇼 Rwanda | $2762.5 | $3453 | $331500 |
| 🇰🇳 Saint Kitts And Nevis | $3155 | $3944 | $378600 |
| 🇱🇨 Saint Lucia | $3230 | $4038 | $387600 |
| 🇻🇨 Saint Vincent And The Grenadines | $3355 | $4194 | $402600 |
| 🇸🇲 San Marino | $2500 | $3125 | $300000 |
| 🇸🇹 Sao Tome And Principe | $2762.5 | $3453 | $331500 |
| 🇸🇱 Sierra Leone | $2762.5 | $3453 | $331500 |
| 🇸🇴 Somalia | $2762.5 | $3453 | $331500 |
| 🇸🇸 South Sudan | $2762.5 | $3453 | $331500 |
| 🇸🇷 Suriname | $3230 | $4038 | $387600 |
| 🇸🇿 Swaziland | $2762.5 | $3453 | $331500 |
| 🇹🇬 Togo | $2762.5 | $3453 | $331500 |
| 🇹🇴 Tonga | $3345 | $4181 | $401400 |
| 🇹🇻 Tuvalu | $3345 | $4181 | $401400 |
| 🇧🇫 Burkina Faso | $2762.5 | $3453 | $331500 |
| 🇼🇸 Samoa | $3345 | $4181 | $401400 |
ShipsFor-Sale.com is a renowned company specializing in the sale of ships. With years of experience in the maritime industry, they have established themselves as a trusted platform for buyers and sellers worldwide. Offering an extensive range of vessels, including cargo ships, tankers, fishing boats, and luxury yachts, ships for sale in greece. Their team of knowledgeable professionals provides expert guidance throughout the buying and selling process, ensuring smooth transactions and customer satisfaction. Whether you are a seasoned ship owner or a first-time buyer, ShipsFor-Sale.com offers a comprehensive selection of vessels and a seamless online experience, making them the go-to destination for ship sales.
